TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

smok pen

TIPS ABOUT HOW TO Extend Smok Pen Recharge Time

The Smok Pen is a new pen that was created by two guys in California. They wanted to develop a cool writing instrument that appeared as if a real pen but had the opportunity to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the marketplace by storm.

The Smok Pen includes a built quality that’s just great. I came across that even though it is an electronic pen the construction is just as good as the pens that I’ve reviewed. This is due to of how they made the top cap. You don’t have to worry about the cap cracking or breaking you Smok Valve Pen.

The two biggest differences that separate the Smok Valve from other pens may be the form of the coils and the way that they are built. Generally the coil on a Smok Pen is larger than on other pens. I believe that they did this on purpose, to help make the pen feel more substantial.

If you take a glance at a Smok Pen, you will observe that your body of the pen is round and not smooth like other pens. On the trunk of the pen you will find a little tab that houses the coil. Once you press on the tab you can actually turn the heating element on and off. I must say i liked this feature because it allows me to use the Smok Pen 22 whenever I feel like smoking.

To use the Smok Pen it is advisable to keep carefully the heat button pressed. After the button is pressed, the heating element will begin to warm up. Once it reaches the appropriate temperature you can turn off the heating element. Smok recommends using a 22mm tank. I prefer a more substantial tank, but that’s just me.

When you put your Smok Pen in to the tank you will see a indicator light seriously. The indicator light will stay green unless you put your Smok Pen in to the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen in to the charger before you apply the e-liquids to the coil heads. It is also important to do that before putting your e-liquids into the coil heads.

After you have completed this step, you should always check to see when you are at the right temperature for the coils to fire. Or even then you should turn the energy off and try again. For anyone who is still not satisfied with your Smok Pen i quickly suggest you take it in for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just usually do not work as they should. I would recommend that you perform the following two steps, then go ahead and check the Smok Pen to see if it still gets the electronic charging port.

Prior to going any further you should remove the battery from your pen and unscrew the magnetic cap. You should then take away the plastic sleeve that holds the sub-ohm. There is a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. Once you have loosened this wire you can then access the sub-ohm. You should then take away the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch any of the coils.

After you have placed the sub-ohm tank in to the pen you should then place all of those other components like the wattage, the batteries and the heating element into the included microwaveable microwave oven. Turn on the power and follow the on screen instructions. You should place the pen’s battery into the microwave and activate the setting. You should then wait approximately 30 seconds before turning it back off. When you initially put the pen in to the microwave the electronic reading will show a minimal voltage protection setting. If this setting does not automatically get set you then should follow the on screen instructions.

After the Smok Pen has reached the temperature that it requires to reach you should then connect the two wires to the negative and positive on the positive post on the Smok unit. You should then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step would be to connect the positive cable to the bottom of the Smok’s on / off switch.

After all the components have been placed in to Novo 2 the pen, you should turn the power on. After the first test run, you should be able to see the battery life indicator light seriously. If you do not see any sign of life from the Smok Pen, you need to take away the battery from the pen and replace it with a brand new one. For your convenience there is also a green light which might be pressed as a way to confirm the battery charging status. Once you have done these things and you also do not start to see the green light indicating charging, you need to replace the battery.

taylor681

Website: